Permabond CA002000016Z0101 200 1 Pound Bottle
Permabond CA002000016Z0101 200 1 Pound Bottle
Permabond 200 is a clear, high-viscosity ethyl cyanoacrylate adhesive for wire tacking, component mounting and rapid bonding of compatible plastics, rubber and metals. SKU CA002000016Z0101 supplies one 1-pound bottle, not a 1-ounce bottle or a case of smaller bottles. Its 1,500 cP viscosity provides more controlled flow than low-viscosity cyanoacrylates, with no mixing or heat cure required.
Best Uses / Applications
Consider Permabond 200 for wire-tacking operations, component bonding and high-speed assembly where a thicker instant adhesive is useful. The 1-pound bottle offers the same 200 grade in a larger individual package. Evaluate the substrates, dispensing method, joint gap and service conditions before committing to production.
Key Features
- One 1-pound bottle, SKU CA002000016Z0101.
- High viscosity: 1,500 mPa·s (cP) at 25°C.
- Single-component ethyl cyanoacrylate, 100% reactive and solvent-free.
- Fast setting without mixing or heat cure.
- Maximum specified gap fill of 0.38 mm (0.015 in).
- Typical 15-second handling time on steel, Buna N rubber and phenolic; full strength in 24 hours.
Technical Specifications
| Specification | Detail |
|---|---|
| SKU | CA002000016Z0101 |
| Grade | Permabond 200 |
| Package | One 1-pound bottle |
| Chemistry | Ethyl cyanoacrylate |
| Uncured appearance | Colorless / clear |
| Viscosity at 25°C | 1,500 mPa·s (cP) |
| Specific gravity | 1.05 |
| Maximum gap fill | 0.38 mm / 0.015 in |
| Typical handling time: steel, Buna N rubber and phenolic | 15 seconds on each substrate |
| Full strength | 24 hours |
| Typical shear strength, steel, ISO 4587 | 22 N/mm² / 3,200 psi |
| Typical shear strength, aluminum, ISO 4587 | 8 N/mm² / 1,200 psi |
| Impact strength, ASTM D-950 | 3–7 kJ/m² / 1.4–3.3 ft-lb/in² |
| Dielectric strength | 250 V/mil |
| Hardness, ISO 868 | 85 Shore D |
| Recommended storage | 2–7°C / 35–45°F |
| Technical reference | Global TDS Revision 2, March 27, 2026 |
Handling time corresponds to achieving 0.3 N/mm² shear strength, not full cure. Temperature, humidity, substrate and gap affect cure speed. Strength results depend on preparation and joint gap. TDS data provide typical guidance rather than guaranteed performance for every application.
Package and Grade Comparison
| Selection factor | This Permabond 200 listing | Alternative |
|---|---|---|
| Package | One 1-pound bottle, CA002000016Z0101 | CA002000001Z0101 supplies ten 1-ounce bottles of the same 200 grade. |
| Viscosity at 25°C | 200: 1,500 cP | 105: 30–50 cP for lower-viscosity flow. |
| Maximum specified gap | 200: 0.38 mm / 0.015 in | 105: 0.1 mm / 0.004 in. |
| Application emphasis | Wire tacking and component bonding where thicker adhesive is useful | 105 suits close-fitting joints, wicking and penetrating applications. |
| Full strength | 24 hours | 105 also develops full strength in 24 hours. |
Choose package size for your workflow and grade for the actual flow requirement, joint design and substrate compatibility. Neither grade is universally preferable for every bond.
Surface Preparation and Directions
Surfaces must be clean, dry and grease-free. Use a suitable degreasing solvent compatible with the substrate. Aluminum, copper and their alloys may benefit from light abrasion to remove the oxide layer.
- Apply adhesive sparingly to one surface.
- Bring parts together quickly and correctly aligned.
- Apply sufficient pressure to spread adhesive into a thin film.
- Do not disturb or realign until sufficient handling strength develops.
- Allow 24 hours for full strength before evaluating final performance.
Surface moisture initiates cure when the adhesive is pressed into a thin film between parts. Difficult or porous surfaces may require a Permabond activator. Larger gaps or acidic surfaces can slow cure; the TDS identifies CSA or QFS 16 as options to address this. For polypropylene, polyethylene, PTFE or silicone, prime first with Permabond Polyolefin Primer (POP).
Storage and Handling
Store at 2–7°C (35–45°F). Allow adhesive to reach room temperature before opening the bottle to prevent internal condensation that can reduce shelf life. The TDS does not recommend contact with strong oxidizing materials or polar solvents. Review the Safety Datasheet before use. For professional or industrial use only; keep out of reach of children.
Manufacturer Application Videos
These general manufacturer guidance videos are referenced in the Permabond 200 Technical Datasheet. They supplement, rather than replace, the grade-specific written directions, TDS and Safety Datasheet.
Frequently Asked Questions
Does this listing contain one bottle or a case?
SKU CA002000016Z0101 contains one 1-pound bottle of Permabond 200. The case of ten 1-ounce bottles is a separate SKU.
Is the adhesive different from the smaller Permabond 200 bottles?
The grade is the same Permabond 200. This listing differs in package size and quantity, not the stated adhesive grade.
What applications suit Permabond 200?
The manufacturer identifies wire tacking and component bonding on compatible plastics, rubber and metals. Its high viscosity is useful where more controlled flow is needed than with a low-viscosity grade.
Does it reach full strength in 15 seconds?
No. Fifteen seconds is the typical handling time on steel, Buna N rubber and phenolic at 0.3 N/mm² shear strength. Full strength takes 24 hours; conditions can change cure speed.
What gap can it fill, and when is primer needed?
The maximum specified gap fill is 0.38 mm (0.015 in). The TDS directs users to prime polypropylene, polyethylene, PTFE and silicone with Permabond POP. Difficult or porous surfaces may need an activator.
How should the 1-pound bottle be stored?
Store at 2–7°C (35–45°F), then allow the adhesive to reach room temperature before opening. This helps prevent condensation inside the bottle and reduced shelf life.
Technical & Safety Documents
Permabond 200 Technical Datasheet, Revision 2 (PDF)
Permabond 200 Safety Datasheet (PDF)
Related Resources
Explore the Permabond collection and our Adhesives, Dispensing & UV Cure Systems guide for related adhesive-selection resources.
