Permabond CA001050016Z0101 105 1 Pound Bottle
Permabond CA001050016Z0101 105 1 Pound Bottle
Permabond 105 is a clear, low-viscosity, high-purity ethyl cyanoacrylate adhesive for fast bonding of tight-fitting parts. SKU CA001050016Z0101 supplies one 1-pound bottle, not a 1-ounce bottle or a case of smaller bottles. This is the same Permabond 105 grade offered in the smaller package; the manufacturer describes its uncured appearance as colorless. Its 30–50 cP viscosity suits thin bond lines, wicking and penetrating applications on compatible plastics, metals, natural rubber and synthetic rubbers.
Best Uses / Applications
Consider Permabond 105 for high-speed assembly, close-fitting plastic parts and natural or synthetic rubber bonding, including EPDM and butyl rubber. The 1-pound package is an option for users who need this grade in a larger individual bottle. The single-component formulation requires no mixing or heat cure. Validate your actual substrates, dispensing method, joint design and service conditions before production use.
Key Features
- One 1-pound bottle of Permabond 105 under SKU CA001050016Z0101.
- Colorless ethyl cyanoacrylate with 30–50 mPa·s (cP) viscosity at 25°C.
- Single component, 100% reactive and solvent-free.
- Surface moisture initiates cure when pressed into a thin film between parts.
- Typical handling times in seconds; full strength in 24 hours.
- Maximum specified gap fill of 0.1 mm (0.004 in).
Technical Specifications
| Specification | Detail |
|---|---|
| SKU | CA001050016Z0101 |
| Product | Permabond 105 |
| Package | One 1-pound bottle |
| Chemistry | Ethyl cyanoacrylate |
| Uncured appearance | Colorless / clear |
| Viscosity at 25°C | 30–50 mPa·s (cP) |
| Specific gravity | 1.1 |
| Maximum gap fill | 0.1 mm / 0.004 in |
| Typical handling time, steel | 10–15 seconds |
| Typical handling time, Buna N rubber, phenolic, PVC and ABS | 5–10 seconds |
| Typical handling time, EPDM | Less than 20 seconds |
| Full strength | 24 hours |
| Typical steel shear strength, ISO 4587 | 18–22 N/mm² / 2,600–3,200 psi |
| Cured hardness, ISO 868 | 85 Shore D |
| Recommended storage | 2–7°C / 35–45°F |
| Technical reference | Global TDS Revision 7, September 13, 2025 |
Handling time is based on achieving 0.3 N/mm² shear strength, not full cure. Cure speed depends on temperature, humidity, surfaces and gap. Strength results also depend on surface preparation and joint gap. TDS values are typical guidance, not guaranteed results for every application.
Package and Adhesive Selection
| Selection question | Guidance |
|---|---|
| What does this SKU contain? | One 1-pound bottle of Permabond 105. |
| How does the smaller-bottle listing differ? | CA001050001Z0101 contains ten 1-ounce bottles of the same 105 grade; it is a different package quantity. |
| Does “clear” mean a different 105 formulation? | No separate grade is indicated. The 105 TDS describes uncured appearance as colorless. |
| Is it suitable for a large gap? | Maximum specified gap fill is 0.1 mm; evaluate a gap-filling grade for larger joints. |
| Can it bond PP, PE, PTFE or silicone without preparation? | The TDS directs users to prime these substrates first with Permabond Polyolefin Primer (POP). |
Surface Preparation, Use and Storage
Surfaces should be clean, dry and grease-free. Choose a suitable degreasing solvent compatible with the substrates. Aluminum, copper and their alloys may benefit from light abrasion to remove the oxide layer.
- Apply adhesive sparingly to one surface.
- Bring components together quickly and correctly aligned.
- Apply sufficient pressure to distribute the adhesive into a thin film.
- Do not disturb or realign until sufficient handling strength develops.
- Allow 24 hours for full strength before evaluating final bond performance.
For difficult or porous surfaces, the manufacturer recommends an appropriate Permabond activator. Larger gaps and acidic surfaces can slow cure. The TDS does not recommend service in contact with strong oxidizing materials or polar solvents.
Store at 2–7°C (35–45°F). Allow adhesive to reach room temperature before opening the bottle to avoid internal condensation that can reduce shelf life. Review the Safety Datasheet before use. For professional or industrial use only; keep out of reach of children.
Manufacturer Application Videos
These general manufacturer guidance videos are referenced in the Permabond 105 Technical Datasheet. They supplement, rather than replace, the grade-specific written directions, TDS and Safety Datasheet.
Frequently Asked Questions
Is this a 1-ounce or 1-pound bottle?
This listing is for one 1-pound bottle, SKU CA001050016Z0101. It is not the case-of-ten 1-ounce package.
Is “105 clear” different from Permabond 105?
This listing identifies the same Permabond 105 grade. Clear describes its appearance; the manufacturer lists the uncured adhesive as colorless.
How fast does it cure?
Typical handling time is 10–15 seconds on steel, 5–10 seconds on Buna N rubber, phenolic, PVC and ABS, and less than 20 seconds on EPDM. Full strength takes 24 hours, and actual times depend on conditions.
What gap can it fill?
The specified maximum gap fill is 0.1 mm (0.004 in). It is intended for close-fitting parts rather than large-gap filling.
Does it need mixing, heat or primer?
No mixing or heat cure is required. The TDS directs users to prime polypropylene, polyethylene, PTFE and silicone with Permabond POP. An activator may be needed on difficult or porous surfaces.
How should the bottle be stored?
Store at 2–7°C (35–45°F). Bring the adhesive to room temperature before opening to prevent condensation inside the bottle, which can reduce shelf life.
Technical & Safety Documents
Permabond 105 Technical Datasheet, Revision 7 (PDF)
Permabond 105 Safety Datasheet (PDF)
Related Resources
Browse the Permabond collection and our Adhesives, Dispensing & UV Cure Systems guide for related adhesive-selection resources.
